Line 6 StageSource Powered PA Speaker W/Mixer - Long & McQuade Music Educator Site
Proudly Canadian since 1956  Canadian Flag
  Main Menu

Line 6 StageSource Powered PA Speaker w/Mixer

Add to Wish List
StageSource L2t loudspeakers use massive DSP and huge power to deliver studio-quality live sound at every gigfrom solo shows to band performances.

Smart Speaker Modes

StageSource L2t loudspeakers use massive DSP unmatched in their classand huge power to deliver studio-quality live sound at every gig. Using six powerful DSP-based Smart Speaker modes, you can optimize the speakers output for a variety of performance scenarios including front-of-house PA, floor monitor, personal PA, keyboard backline, acoustic guitar backline, or with a multi-effects guitar processor as a high-performance electric guitar speaker system. An onboard accelerometer and pole-mount sensors automatically detect the speakers orientation and set the Smart Speaker mode accordingly.

Integrated Multi-channel Mixer with Effects

The L2t can function as a self-contained live sound solution. With a full-featured onboard mixer including multiple inputs for microphones, instruments, external mixers and MP3 players, L2t delivers all of the tools you need for great live sound.

Integrated Feedback Suppression

Since feedback can ruin a performance, StageSource L2t uses intelligent 12-band feedback suppression to identify the problem frequencies and adjust levels without affecting the overall sound.

L2t feedback suppression continuously analyzes the audio signal, identifying frequencies that have the characteristics of feedback (steady frequencies with few overtones, rising in amplitude) and then applies a narrow notch filter to remove the offending frequency. L2t feedback suppression can remove up to 12 independent feedback frequencies. You can set the feedback analyzer to one of three modes, depending on how aggressively the analyzer will seek out potential feedback frequencies.

Fast Networking via L6 LINK

In live sound situations where two or more speakers are needed, StageSource products use a proprietary digital networking protocol called L6 LINK to simplify setup. Loudspeakers will automatically self-configure, pan stereo signals, adjust Smart Speaker modes and perform system-wide optimization. Add StageSource L3s subwoofers to the mix and the system automatically sends them the summed signals and sets the crossovers. When combined, Line 6 live sound products form an intelligent ecosystem that sets up faster and helps you sound your best.

Multi-function Design and Scalability

Multi-function design combined with powerful Smart Speaker modes and digital networking provides true scalability whether youre using a single L2t as a standalone PA or multiple L2t and L2m speakers as main PA, monitors and backline. Add StageSource L3t/L3m loudspeakers and L3s subwoofers to customize a configuration that meets your live sound or installation needs.


Road-ready Construction

StageSource L2t is ready for whatever the road can throw at it. The robust enclosure is constructed of heavy-duty plywood and a tour-grade steel grille with protective screen backing that protects the drivers from impact damage.

If you need to fly the speakers, each StageSource L2t features four professional M10 suspension points with a pull-back.

Specifications

Acoustical Specifications
System Type: 10, 2-way, bi-amplified loudspeaker system
Frequency Range (-10dB): 44Hz to 19kHz, (Reference/P.A. Speaker Mode, free-field)
Frequency Response (3dB): 51Hz to 18kHz, (Reference/P.A. Speaker Mode, free-field)
Maximum SPL Output: 128dB peak @ 1 meter (unweighted, measured indoors with music program material)
Coverage Pattern (-6dB): 100 x 50 degress
Directivity Factor (Q): 9.2 (averaged 1kHz to 16kHz)
Directivity Index (DI): 9.6dB (averaged 1kHz to 16kHz)
Crossover Frequencies: LF to HF Crossover - variable, 2.2kHz to 7.0kHz (Speaker Mode dependent)
Low-Frequency Transducer: 10 extended range woofer, 2 diameter voice coil, 4Ω impedance
High-Frequency Transducer: 1 exit compression driver, 1.4 diameter voice coil and diaphragm, 8Ω impedance

Electrical Specifications Rear Panel
Input Types: Line-level XLR-1/4, balanced Stereo RCA, unbalanced, L6 LINK XLR
Input Impedance: 100k balanced, 20k balanced, N/A
Max Input Levels: +20dBu, +16dBV, N/A
Onset of Limiting: +6dBu input (Reference/P.A. Speaker Mode, Master Level control at center-detent), -6dBu input (Reference/P.A. Speaker Mode, Master Level control at maximum)
Output Types: Balanced Loop Thru XLR, Balanced Mix Out XLR, L6 LINK XLR
Output Impedances: Source-dependent 680Ω balanced, N/A
Controls: Feedback Suppression On/Off/Mode, Master Level, Speaker Mode
Indicators: Signal Present/Clip, Feedback Suppression On/Off/Mode, Limit, 6x Speaker Mode, L6 LINK Status
Electrical Side Panel
Input Type: 2x mic/instrument XLR-1/4, balanced
Input Impedance (each input): 2.63k balanced (Pad = 0dB), 23.7k balanced (Pad = 20dB)
Gain Range (each input): -infinity to +57dB (Pad = 0dB); -infinity to +37dB (Pad = 20dB)
Max Input Level: +25dBu (Gain at minimum on position, 20dB pad on)
Controls: 2x Gain, 20dB Pad, LF Level, MF Freq & Level, HF Level, Mod Level, Reverb Level, Feedback Suppression On/Off/Mode, 1x Dual Mono/Stereo Link Mode, Acoustic Modeling Amount, On/Off
Indicators: 2x Signal Present/Clip, 2x Feedback Suppression On/Off/Mode, 1x Acoustic Modeling On/Off
Digital Signal Processing
Speaker Modes: Reference/P.A., Playback, Floor Monitor, Keyboards, Acoustic Guitar, Electric Guitar
On-board Effects: Reverb, Modulation, Feedback Suppression, Acoustic Modeling
Transducer Protection: Excursion limiting, thermal limiting
Digital Networking: L6 LINK intelligent speaker networking system
Sensors: Speaker orientation, pole sensor, power amp temperature, power supply, temperature
Power Amplification and Supply
Output Channel: HF LF
Power Amplifier Types: Class AB, Class D
Peak Output Power: 175 watts 655 watts
Power Supply Voltage Range: 100 - 240 VAC, 10%, 50/60Hz , automatic voltage selection
Power Consumption: 250 watts (1/8th power)
Cooling: Digitally-controlled, variable-speed 50 mm fan
Protection: Output overcurrent, overtemperature, DC fault 1 1kHz sine wave input, 1% THD+N unweighted into the nominal load impedance, single channel driven, before the onset of limiting.
Mechanical
Enclosure: 15 mm enclosure, 18 mm baffle, multi-ply hardwood, textured black paint, bass, reflex design
Floor Monitor Upward Angle: 60 degrees using kickstands, 30 degrees using handle
Suspension Points: M10 x 1.5 threaded inserts, qty: 4
Pullback Point: M10 x 1.5 threaded insert, qty: 1
Grille: 18-gauge perforated steel, black powder coat finish
Pole Cup: 35 mm pole cup with sensor
Dimensions (HxWxD): 23.75 (603 mm) x 12.25 (312 mm) x 12.25 (312 mm)
Weight: 39.1 lb (17.7 kg)

Amazingly versatile0 of 0 customers found this review helpful

FeaturesProduct ratingProduct ratingProduct ratingProduct ratingProduct rating
QualityProduct ratingProduct ratingProduct ratingProduct ratingProduct rating
ValueProduct ratingProduct ratingProduct ratingProduct ratingProduct rating
OverallProduct ratingProduct ratingProduct ratingProduct ratingProduct rating
Product ExperienceI own it
Closest StoreWoodstock, Ontario
I have 2 of these that I use with my Helix. They sounds absolutely amazing. Having the 2 channel mixer on each makes it a 4 channel PA system perfect for rehearsals and small gigs. Small enough to be tramsported easily (I highly recommend the Line 6 bags and casters) the perfecf all in one solution for amplifying your modeller as well as small PA solution. A bit pricey but built like a tank.
Posted by anonymous on Feb 22, 2018
Was this review helpful?    flag review
Sale Price: $799.00
Store Special Product - StageSource Powered PA Speaker w/Mixer
Model: L6L2T
Serial: l2t1f6734000024
Quantity Available: 1
Condition: Used
Store Special Product - StageSource Powered PA Speaker w/Mixer Store Special Product - StageSource Powered PA Speaker w/Mixer