Lectrosonics MT2 IEM/IFB Transmitter W/Dante Inputs - Long & McQuade Music Educator Site
Proudly Canadian since 1956  Canadian Flag
  Main Menu

Lectrosonics MT2 IEM/IFB Transmitter w/Dante Inputs

Departments > Pro Audio & Recording > Headphones > In-Ear Monitors - Wireless > Lectrosonics > MT2 IEM/IFB Transmitter w/Dante Inputs
Add to Wish List
The M2T half-rack transmitter houses two stereo transmitters to provide two stereo audio channels, and for up to four mono audio channels in a single rack space. The audio inputs can be individually configured to be analog or Dante compatible. The analog input connectors are full-size XLR/TRS combo types for balanced line-level analog signals while the input preamp circuits use a special balanced amplifier with very high common mode rejection to minimize hum and noise. A Dante Ultimo interface via dual RJ45 connectors accepts Dante networked audio inputs and can daisy chain the digital stream to additional units via CAT6 cables. An additional RJ45 jack provides an Ethernet connection for programming and control via Wireless Designer software and a USB jack on the front panel allows for firmware updates. The transmitter features a full colour, backlit LCD for high visibility in any environment, while the chassis is all-metal and can be racked singly or in pairs using included rack mount hardware.

• IEM (Wireless Monitor) with digital RF transmission
• 24-bit digital audio
• 2 independent stereo audio transmissions per 1/2 RV enclosure
• USB port for firmware updates
• Fully Dante compatible
• IR (infrared) port for fast setup
• Up to 50 mW per RF carrier
• All metal housing
• Compatible with Wireless Designer Software

Dante Benefits
• Plug-and-play technology automatic discovery and simple signal routing
• Reduced Cost & Complexity- No special skills required to set up audio networking
• Sample accurate playback synchronization
• Lowest latency available from any networking technology
• Add/remove/rearrange components at will
• Deterministic latency throughout the network
• Support mixed bit depths and mixed sample rates over one network
• Scalable, flexible network topology supporting a large number of senders and receivers
• Supports 1Gbps networks
• Supports a single integrated network for audio, video, control, monitoring
• Uses inexpensive, off-the-shelf computer networking equipment

Specifications

RF Power Output:
• Two carriers; two audio channels each
• Power adjustable on each carrier to 10, 25 or 50 mW
Antenna Output: 2 x BNC sockets
Operating Frequencies: 470.100 - 607.975 MHz
Frequency Selection Steps: 25 kHz
Frequency Stability: +/- 0.002%
Modulation: 8 PSK
Emission Designator: 200KG7E
Spurious Radiation: Compliant with ETSI EN 300 422-1
Equivalent input Noise: 128 dBV
Latency: (overall system)
• Digital Source: 1.0 ms plus Dante network
• Analog Source: < 1.4 ms
Audio Frequency Response: 20 Hz - 15 kHz
Audio Input: -10 dBV or +4 dBu settings; +/-5 dB trim
Audio Input Jack: 4 x combo XLR/TRS connectors
Input impedance: Line: 2k Ohm
Dante Connection: 2 x RJ45, 4 audio RX channels, internally routable
Ethernet Connection: RJ45
USB Connection: Micro USB on front panel for firmware updates
IRDA: IR transceiver for sync of receivers
Headphone jack 3.5 mm stereo jack
Power Requirements: 9-18 VDC
Power Consumption: 5 Watts

Dimensions:
Height: 1.750 in. / 44.45 mm
Width: 8.375 in. / 212.7 mm
Depth: 7.750 in. / 196.8 m.
Weight: 2.2 lbs (997.903 grams)
There are currently no reviews for this product, be the first to write one!