BOSS Solderless Pedalboard Cable Kit W/12 Connectors, 12 Ft Cable - Long & McQuade Music Educator Site
Proudly Canadian since 1956  Canadian Flag
  Main Menu

BOSS Solderless Pedalboard Cable Kit w/12 Connectors, 12 ft Cable

Departments > Guitars > Cables & Power Supplies > Cables - Guitar > BOSS > Solderless Pedalboard Cable Kit w/12 Connectors, 12 ft Cable
Add to Wish List
SKU: # 687356
Model: #

BCK-12

4 models to choose from:

Online

The BOSS Solderless Pedalboard Cable Kit is designed to save space on your pedalboard without sacrificing tone. Easy to assemble, this customizable system requires only the tightening of a single ground screw on each connector, with no cable stripping required. The compact bi-directional connectors are engineered to allow straight or right-angle connections, and enable you to place your pedals as close as 1 cm apart.

Premium 24K gold plated contacts ensure the most precise sound reproduction available. The low-capacitance, studio-grade cable is ultra-pliable for clean cable management, and is manufactured with oxygen-free copper and braided shielding for quiet operation and lasting durability.

• Solderless technology for simple and quick assembly
• Bi-directional barrel design with 24K gold-plated contacts
• Low-capacitance cable preserves your tone
• Ultra-pliable cable for easy cable management
• 2.5 mm screwdriver included
• Available kit sizes: BCK-2, BCK-6, BCK-12, BCK-24

Works just fine.0 of 0 customers found this review helpful

FeaturesProduct ratingProduct ratingProduct ratingProduct ratingProduct rating
QualityProduct ratingProduct ratingProduct ratingProduct ratingProduct rating
ValueProduct ratingProduct ratingProduct ratingProduct ratingProduct rating
OverallProduct ratingProduct ratingProduct ratingProduct ratingProduct rating
Product ExperienceI own it
Closest StoreEdmonton Northeast, Alberta
This is a DIY kit. At the end of the day, it will work as well as any DIY kit will. The quality of the cables and the connectors are just fine. Being a soldier less joint, you really need to make sure the joint is pushed in tight, but otherwise they work fine. Be sure to check cables with a multimeter during install. When installed correctly, I found that these cables had lower resistance readings than the other ?pro? cables on my board. I only had 1 cable out of 12 that exhibited a volume drop, and it was because I installed it with a partial short between the hot wire and the shroud. The solution? Snip off 1/8 inch of the faulty cable and reinstall the jack. Easy as that. With some care and patience, a simple multimeter and basic skill, this product works great.
Posted by Nick on Sep 16, 2018
Was this review helpful?    flag review

Do not buy this product. Garbage.0 of 1 customers found this review helpful

FeaturesProduct ratingProduct ratingProduct ratingProduct ratingProduct rating
QualityProduct ratingProduct ratingProduct ratingProduct ratingProduct rating
ValueProduct ratingProduct ratingProduct ratingProduct ratingProduct rating
OverallProduct ratingProduct ratingProduct ratingProduct ratingProduct rating
Product ExperienceI've tried it
Closest StoreToronto (Bloor St.), Ontario
I've spent probably and hour and a half to build 4 cables that I test, doesn't work, unscrew the screws, reseat the cable in the socket end, do the same to the other end, test again, not working... and repeat. Very frustrating. I had some cables I made had a very week signal ... half the volume of a soldered cable. I'd be weary about using this on a pro board.
Posted by Michael on Aug 5, 2018
Was this review helpful?    flag review

Not recommended0 of 0 customers found this review helpful

FeaturesProduct ratingProduct ratingProduct ratingProduct ratingProduct rating
QualityProduct ratingProduct ratingProduct ratingProduct ratingProduct rating
ValueProduct ratingProduct ratingProduct ratingProduct ratingProduct rating
OverallProduct ratingProduct ratingProduct ratingProduct ratingProduct rating
Product ExperienceI own it
Closest StoreWinnipeg North, Manitoba
I have this solderless cable and the quality is not there. it's too soft, the connection is too sensitive and I would not count on it. I usually use George L's which is superb at any class. it's expensive, can do it's job but in this case I prefer to solder...
Posted by Adir on Jul 23, 2018
Was this review helpful?    flag review